Palsonic Home Theater System PMC 191 User Manual

INSTRUCTION MANUAL  
MICRO COMPONENT SYSTEM  
PMC-191  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL: (02) 9313 7111  
FAX: (02) 9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
 
LISTENING TO RADIO  
Manual Tuning  
1.  
2.  
3.  
Set Function Selector to "Tuner" position.  
Set Band button to the desired band.  
Press Manual Tuning "UP" button or Manual Tuning "DOWN" button until your desired station is  
reached.  
4.  
Adjust the volume control to the appropriate level as desired.  
Auto Tuning  
Follow steps 1, 2 of "Manual Tuning".  
Press UP or DOWN button continuously to start the automatic tuning.  
To terminate Auto Tuning, press the UP or DOWN button again.  
1.  
2.  
3.  
PROGRAM INDICATOR  
BAND  
INDICATOR  
STEREO  
INDICATOR  
STATION NO.  
FREQUENCY INDICATOR  
Preset Stations by Remote Handset  
This unit equipped 10 preset station for FM and MW, 5 station for LW if LW is available. Once they are  
preset broadcasting corresponded to those can readily be enjoyed by simply pressing the Preset Station  
button.  
Set in Tuner mode.  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Your desired station can be received by "Manual Tuning" or "Auto Tuning".  
Press the MEMORY button (at Remote), to enable program state.  
Press the M-UP / REPEAT button (at Remote), to adjust preset station number.  
Frequency is written in the Preset a Memory by pushing MEMORY button once again.  
Repeat step 2 to step 5 to enter additional channels into Program.  
To return normal Tuner mode, leave keys free.  
.
Remarks: There are 5 seconds for program state. After 5 seconds this state would release automatically.  
Calling the Preset Stations  
Press the M-UP / Repeat Key (at Remote) to select the Preset Station in order.  
FM & FM-Stereo Reception  
.
.
Set FM mode selector at "MONO" position. Programs are received in Mono mode. In particular when  
stereo signals are weak, it is preferable to receive the program in MONO.  
Set FM mode selector at "STEREO" position for receiving stereo programs.  
Beat Cut  
When beats are produced while listening to recording an AM broadcast, active the beat cut switch so the  
beats are eliminated or minimised.  
PLAYING COMPACT DISC  
Getting Started  
1.  
2.  
3.  
Set Function Selector to CD mode. lift up the CD door and put a disc into the Compact  
Disc Compartment, then close the Compartment.  
The Display will show "00" for a few seconds, then the total number of tracks and the total playing  
time of the disc.  
"DISC' will be displayed when there is no disc inside the compartment.  
2
 
REPEAT  
INDICATOR  
RANDOM  
INDICATOR  
PROGRAM  
INDICATOR  
MIN  
SEC  
TRACK NO.  
General Operation  
Press once to start play, press once again to stop the || disc play  
temporarily. When CD player is paused, display is blinking.  
Press to stop play.  
PLAY / PAUSE Button  
STOP Button  
SKIP Buttons  
Press once to skip to next track  
UP/ | and DOWN / |  
| or back to previous track  
|
Press once, the display will show a "Random".  
RANDOM Button (at Remote)  
Press the Play button to play the disc in random order. When CD  
is playing in Random mode, press UP /  
randomly.  
| to select another track  
Press the Random button again to terminate the Random display.  
.
During CD Play Random Play is started by pressing the RANDOM button once.  
To obtain optimum sound performance for CD, select the switch at the back to CD position.  
.
Program Play (For CD only) by Remote  
Up to 20 tracks can be programmed for disc play in any order. Before use, be sure to press the Stop button.  
STATION NO.  
PROGRAM NO.  
Set in CD mode.  
1.  
2.  
Press the MEMORY button (at remote), the display will show blinking "Track" and "Memory".  
Moreover, it will indicate program no. and digits for track no. to be programmed.  
Select a desired track by using the Skip buttons.  
Press the MEMORY button again to enter the track into the program.  
Repeat steps 2 and 3 to enter additional memories into the program, if necessary.  
When all the desired tracks have programmed, press PLAY / PAUSE button to play the disc in the  
order you have programmed. The display will show the Program Indicator "MEMORY" to identify  
this function.  
3.  
4.  
5.  
6.  
Press STOP button to terminate program play.  
7.  
.
Remarks: There are 5 seconds for memory writing enable state, after that the state would released  
automatically.  
Notes:  
The program memory will be cleared when the Power button is set to "OFF", when CD mode is  
changed to other modes, or when EJECT button is pressed.  
During program play, press UP / | button to select the programmed track in order.  
1.  
2.  
3
 
You can repeat all programmed tracks endlessly by this function.  
Follow stop 1 to step 5 in Program Play.  
Press M-UP / REPEAT button.  
To cancel Repeat Play, press the M-UP / REPEAT button again.  
1.  
2.  
3.  
Repeat Play (For CD only) by Remote  
Single Track Repeat Play (only available for normal playing)  
You can repeat a particular track of the disc endlessly by this function.  
1.  
2.  
3.  
4.  
5.  
Select a desired track by Skip buttons.  
Press M-UP / REPEAT button twice at Remote.  
The display will show "REPEAT" and flashing, and repeat function would be initialised.  
Press PLAY / PAUSE Button to start.  
To cancel repeat play, press the M-UP / REPEAT button one again.  
.
Remarks: To repeat the track that is playing, press the M-UP /REPEAT button twice.  
All Tracks Repeat Play (available for both normal playing and programmed playing)  
You can repeat the entire disc endlessly by this function.  
1. Press M-UP / REPEAT button once.  
2. The display will show "REPEAT".  
3. Press PLAY / PAUSE button to start.  
4. To cancel repeat play, press the M-UP / REPEAT button twice.  
Playing the Beginning of each Track (INTRO)  
The Intro feature lets you sample all of the CD tracks for 10 seconds.  
1.  
2.  
Press INTRO. Intro play will begin with Track 1.  
To cancel Intro play and begin normal play, press INTRO again.  
LISTENING TO TAPE  
General Operation  
Stop / Eject key  
Press to stop all deck operations. Press again to the Cassette Doors.  
Fast Forward Key  
Fast Rewind Key  
Press to start rapid tape winding in either forward or reverse direction.  
Press Stop / Eject Keys when the cassette spools stop turning.  
Play Key  
Press to start playing a tape.  
Pause Key  
Record Key  
Press to stop tape operation temporarily. Press again to resume tape operation.  
Press together with Play Key to start recording.  
Playback  
-
-
-
-
-
-
Set the Function selector to TAPE position.  
Put in your cassette tape.  
Press Play Key to activate playback.  
Adjust the Volume Control to the desired level.  
Use Pause Key when you want to stop playback temporarily.  
Press Stop / Eject Key when finished.  
4
 
RECORDING  
A. Recording From Radio  
.
.
.
.
Set in Tuner mode.  
Tune in your station and put in your cassette tape.  
Press Record Key and the Play Key of deck at the same time to start recording.  
Press STOP / EJECT Key when finished.  
NOTE: If beat noise is present when recording. Adjust the position of the Beat Cut switch on mode  
selector ( For AM / MW or LW Band only).  
B. Recording From CD  
.
Set Function selector to "CD" position.  
Insert a cassette suitable for recording, press pause key then press record  
key. Recording function will be on stand by.  
Activate the CD player, and then press (to release) pause key to start recording.  
To stop recording, first press STOP button on CD player - then press the STOP / EJECT key on tape  
deck.  
.
.
.
REMOTE CONTROL TRANSMITTER  
CONTROL FUNCTIONS  
1.)  
2.)  
3.)  
4.)  
5.)  
6.)  
7.)  
8.)  
9.)  
POWER  
1
2
15  
13  
DIRECT SEARCH KEYS  
VOLUME UP / DOWN  
SKIP DOWN BUTTON  
SKIP UP BUTTON  
MODE BUTTON  
RANDOM BUTTON  
SCAN-UP BUTTON  
BAND SELECTOR  
14  
5
12  
11  
3
7
4
6
8
10  
9
10.) MEMORY BUTTON  
11.) M-UP / REP BUTTON  
12.) INTRO BUTTON  
13.) PLAY / PAUSE BUTTON  
14.) STOP BUTTON  
15.) MUTE  
BATTERY INSTALLATION  
THE INFRARED TRANSMITTER REQUIRES 3.0 VOLTS FOR OPERATION. (UM-4/AAA SIZE)  
Button Description  
PLAY/PAUSE  
- IN CD MODE, PRESS ONCE TO START PLAYBACK. PRESS ONCE AGAIN TO  
STOP THE DISC PLAY.  
TEMPORARILY.  
STOP  
- PRESS TO TERMINATE CD PLAYBACK.  
SKIP |  
SKIP  
REPEAT  
MEMORY  
RANDOM  
- PRESS ONCE TO SKIP TO PREVIOUS TRACK.  
- PRESS ONCE TO SKIP TO NEXT TRACK.  
- IN CD MODE, PRESS TO ENABLE REPEAT PLAY.  
- IN CD / RADIO MODE, PRESS TO ENTER PROGRAM MODE.  
- IN CD MODE, PRESS TO ENTER RANDOM MODE.  
|
5
 
SPECIFICATIONS  
GENERAL  
Power Supply:  
240V/50Hz  
30 Watt  
2 x 5W  
Power Consumption:  
Output Power (RMS):  
Terminal Impedance:  
Unit Dimensions:  
Unit Weight:  
Speaker 4.0 OHMS, Phones 32 OHMS  
188(L) x 230(W) x 279(H) mm  
7 kgs  
CASSETTE SECTION  
4.75 cm/sec  
AC BIAS  
DC MAGNET  
125-6300Hz  
Tape Speed:  
Recording System:  
ErasingSystem:  
Frequency Response:  
CD SECTION  
Channel:  
S/N Ratio:  
2 Channels  
60dB  
Sampling Frequency:  
Disc Size:  
Frequency Response:  
44.1kHz  
75 or 120 mm  
125Hz - 20kHz  
RADIO SECTION  
Tuning Frequency:  
AM: 511 - 1620KHz  
FM: 87.5 - 108MHz  
6
 
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL: (02) 9313 7111  
FAX: (02) 9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
 

Nady Systems Stereo System MM242 User Manual
NEC Computer Monitor 50 User Manual
NeumannBerlin Microphone 1M 214 User Manual
Nortec Industries Humidifier NHTC Series User Manual
Nortel Networks Digital Camera P7000 User Manual
Nu Technology Computer Hardware 6U Compact PCI Highly Integrated Single Slot Dual Bridge Low Power Pentium III CPU Module User Manual
Omega Engineering Stud Sensor LVRD500 User Manual
Omnimount TV Mount OM10324 User Manual
Omron Network Card CJ1W ETN11 User Manual
Panasonic Flat Panel Television BT LH1710E User Manual